CREATE_MESSAGE_MODULE install_tape_menu$us_english

CREATE_brief_help_message
+X2+N0This display shows your current installation parameters, you may
 change them, enter GO to accept them, or enter QUIT if
 you do not wish to proceed with the installation.
+N+X2
**

CREATE_FULL_HELP_MESSAGE
+N0This menu asks you for information necessary to install an installation
 tape.  You must:
+N1 a. Identify the tape by supplying VSN and type information,
+N1 b. Supply the name to use for the packing list from the tape,
+N1 c. Indicate if you want to keep old copies of the software which is
+N5being installed.
+N0To get general help for a particular selection, enter the number
 of the selection, followed by a question mark.
 For example, to get help for selection 1, you would enter:
+N+X2
+N2 1?
+N+X2
+N0Detailed help for each item is available at the prompt for each item.
+N+X2
**

CREATE_PARAMETER_PROMPT_MESSAGE n=packing_list
+X2+P1.+X2Name to assign the packing list ........... +P2
**

CREATE_PARAMETER_PROMPT_MESSAGE n=external_vsn
+X2+P1.+X2External VSN of the installation tape .....'+P3'
**

CREATE_PARAMETER_PROMPT_MESSAGE n=recorded_vsn
+X2+P1.+X2Recorded VSN of the installation tape .....'+P4'
**

CREATE_PARAMETER_PROMPT_MESSAGE n=tape_type
+X2+P1.+X2Type of the installation tape ............. +P5
**

CREATE_PARAMETER_PROMPT_MESSAGE n=save_previous_cycles
+X2+P1.+X2Save previous file cycles ................. +P6
**

CREATE_PARAMETER_PROMPT_MESSAGE n=prompt
+X2+N0Enter a menu selection, GO, QUIT, or ? for HELP.
**

CREATE_PARAMETER_HELP_MESSAGE n=packing_list
+X2+N0The installation tape contains a packing list which describes
 the contents of each tape in your order.+X2This prompt asks for a name
 to assign the packing list when it is loaded from the installation tape
 and stored on disk.+X2The packing list is stored in the installation
 data base catalog managed by the INSTALL_SOFTWARE utility.
+N+X2
**

CREATE_PARAMETER_HELP_MESSAGE n=external_vsn
+X2+N0The external VSN, along with the recorded VSN, are used to request
 the installation tape.+X2Tapes manufactured
 by Software Manufacturing and Distribution (SMD) show the external
 VSN in the media number field of the tape sticker.+X2The installation tape
 will contain the identifier 'FULL/PACKING LIST' in the name field of the
 tape sticker.
+N+X2
**

CREATE_PARAMETER_HELP_MESSAGE n=recorded_vsn
+X2+N0The recorded VSN, along with the external VSN are used to request
 the installation tape.+X2Tapes manufactured
 by Software Manufacturing and Distribution (SMD) use the same
 same external and recorded VSN's.+X2The recorded VSN is often referred
 to as an internal VSN.
+N+X2
**
CREATE_PARAMETER_HELP_MESSAGE n=tape_type
+X2+N0The tape type signifies the the density and the device class for the
 installation tape.+X2Tapes manufactured
 by Software Manufacturing and Distribution (SMD) show the density
 in the density field of the tape sticker.+X2The installation tape
 will contain the identifier 'FULL/PACKING LIST' in the name field of the
 tape sticker.+X2If the density is listed as 1600 bpi or 6250 bpi,
 the device class is 9 track and the tape type would be designated as
 MT9$1600 or MT9$6250, respectively.+X2If the density is listed as 38000
 bpi, the device class is 18 track and the tape type would be designated
 as MT18$38000.  The default is MT9$6250.
+N+X2
**

CREATE_PARAMETER_HELP_MESSAGE n=save_previous_cycles
+X2+N0You may choose to save the previous cycles of
 files that are being installed or have them deleted.+X2Having the files
 deleted will conserve approximately 40 million bytes of disk space on
 your system.
+N0If you are installing your NOS/VE system for the first time, this
 option has no effect on your system's file space.
+N+X2
**

CREATE_PARAMETER_PROMPT_MESSAGE n=packing_list_prompt
Enter the name to assign the packing list or ? for help.
**

CREATE_PARAMETER_HELP_MESSAGE n=packing_list_prompt
+X2+N0The packing list name must have from 1 to 16 characters
 and be a valid SCL name, ie. start with a letter.+X2A typical value for the
 packing list name is the NOS/VE release level.+X2Note that
 the name supplied must not already be in use in the installation
 data base catalog where the packing list will be stored, unless
 prior to upgrading, you loaded the packing list to installed the
 PRE_INSTALL_SW product.+X2In that case, you may use the same packing
 list name again.+X2(This will be checked for you.)
+N+X2
**

CREATE_PARAMETER_PROMPT_MESSAGE n=external_vsn_prompt
Enter the external VSN of the installation tape or ? for help.
**

CREATE_PARAMETER_HELP_MESSAGE n=external_vsn_prompt
+X2+N0The external VSN must have from 1 to 6 characters and be
 a valid NOS/VE tape VSN.+X2Put single quotes around your entry.
+X2Tapes manufactured
 by Software Manufacturing and Distribution (SMD) show the
 VSN in the media number field of the tape sticker.
+N+X2
**

CREATE_PARAMETER_PROMPT_MESSAGE n=recorded_vsn_prompt
Enter the recorded VSN of the installation tape or ? for help.
**

CREATE_PARAMETER_HELP_MESSAGE n=recorded_vsn_prompt
+X2+N0The recorded VSN must have from 1 to 6 characters and be
 a valid NOS/VE tape VSN.+X2Put single quotes around your entry.
+X2Tapes manufactured
 by Software Manufacturing and Distribution (SMD) use the same recorded
 and external VSN's.+X2The recorded VSN is often referred to as an
 internal VSN.
+N+X2
**

CREATE_PARAMETER_PROMPT_MESSAGE n=tape_type_prompt
Select type:
+N0+X3a.+X2MT9$1600
+N0+X3b.+X2MT9$6250
+N0+X3c.+X2MT18$38000
+N0Enter selection or ? for help.
**

CREATE_PARAMETER_HELP_MESSAGE n=tape_type_prompt
+X2+N0When selecting the tape type, you may enter either the selection
 identifier (a, b, c) or the tape type designator (mt9$1600, mt9$6250,
 mt18$38000).
+N+N0Tapes manufactured
 by Software Manufacturing and Distribution (SMD) show the density
 in the density field of the tape sticker.+X2The installation tape
 will contain the identifier 'FULL/PACKING LIST' in the name field of the
 tape sticker.+X2If the density is listed as 1600 bpi or 6250 bpi,
 the device class is 9 track and the tape type would be designated as
 MT9$1600 or MT9$6250, respectively.+X2If the density is listed as 38000
 bpi, the device class is 18 track and the tape type would be designated
 as MT18$38000.  The default is MT9$6250.
+N+X2
**

CREATE_PARAMETER_PROMPT_MESSAGE n=save_previous_cycles_prompt
Do you want to save previous file cycles of the software?+N0Enter True,
 False, or ? for help.
**

create_parameter_help_message  n=save_previous_cycles_prompt
+X2+N0If you would like to save the previous cycles of
 files that are being installed, enter TRUE.+X2If you would like the
 installation to delete the previous cycles, enter FALSE.+X2By
 entering FALSE, the installation will conserve
 disk space by deleting all but the HIGH cycle of the files being
 installed.
+N+X2
**
END_MESSAGE_MODULE
