~"CREATE_MESSAGE_MODULE RMM$DEDICATED_MAINT$US_ENGLISH
~"CREATE_BRIEF_HELP_MESSAGE
                     NOS/VE Maintenance Access Menu

  Status            : Maintenance access to an element is requested.
  Requested Element : ~P1

    You have the following choices:

~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=TERMINATE_REQUEST
       1 - Terminate the request (include a reason with this menu selection).
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=ALLOW_MAINTENANCE
       2 - Allow maintenance access after making sure that the requested
           element is DOWN, OFF, or UNCONFIGURED on mainframes:
             ~P2
             ~P3
             ~P4
             ~P5
~"**
~"CREATE_FULL_HELP_MESSAGE
      This menu asks you to confirm or deny maintenance access to an element
      that is physically accessible to more than one mainframe.  You should
      allow maintenance access from this mainframe only if you are sure that
      the element (~P1)
      is not in use on the mainframes identified.

~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=TERMINATE_REQUEST
      This choice denies the job maintenance access to the element.  Abnormal
      status is returned to the job.  Selection of this choice allows you
      to explain why maintenance access was denied.  For example:

      1 the tape unit that you requested is required for file backup until 5pm

      Your explanation is returned to the job within the abnormal status that
      is generated by this menu choice.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=ALLOW_MAINTENANCE
      This choice confirms that the job may have maintenance access to an
      element that is physically connected to multiple mainframes.  Before
      you select this choice, ensure that the element is DOWN, OFF, or
      not configured on the mainframes identified in the menu; otherwise,
      enter selection 1.
~"**
END_MESSAGE_MODULE CREATE_MODULE=YES
~"CREATE_MESSAGE_MODULE RMM$EXTEND_LABELED$US_ENGLISH
~"CREATE_BRIEF_HELP_MESSAGE
                     NOS/VE Labeled Volume List Extension Menu

  Status                 : An additional LABELED (scratch) volume is requested.
  Group                  : ~P1
  Location               : ~P2
  Requested Density      : ~P3
  Requesting Family Name : ~P4
  Requesting User Name   : ~P5
  Previous External VSN  : ~P6
  Previous Recorded VSN  : ~P7

    You have the following choices:

~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=CONTINUE_REQUEST
       1 - Use CREATE_BLANK_LABELED_VOLUME, if necessary, to label the volume;
           mount it; and identify the 1 to 6 character vsn in the menu
           selection (i.e. 1 RVSN='string' or 1 RVSN=name).
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=TERMINATE_REQUEST
       2 - Terminate the request (include a reason with the menu selection).

~"**
~"CREATE_FULL_HELP_MESSAGE
      This menu is presented because a job is requesting an additional
      labeled volume.  An additional volume is required when the job has
      exhausted the list of volumes identified by either a
      REQUEST_MAGNETIC_TAPE command or an ATTACH_FILE command.

      If you provide an additional volume, the job's volume list is
      automatically updated with the volume that you provide.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=CONTINUE_REQUEST
      This choice identifies the volume that is to be added to the job's
      volume list.  The job requires a labeled volume.  If you intend to
      provide the job with an additional volume, do the following:

        1. Use the INITIALIZE_TAPE_VOLUME command to label the volume for
           the job, if necessary.
        2. Mount the volume on a tape unit and ready the unit.
        3. Enter the RECORDED_VSN using this menu choice.  If the EXTERNAL_VSN
           is different than the RECORDED_VSN, you must provide both, e.g.
               1 RVSN=XXXXXX EVSN=YYYYYY

           You may enter the value in the form of a string or an SCL name.  A
           string representation is required either when the VSN begins with a
           number or when special characters are used in the VSN.  For example:
             To enter an SCL name: 1 RVSN=VE0496
             To enter a VSN beginning with a number: 1 RVSN='901204'
               The latter produces 901204 as the RECORDED_VSN.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=TERMINATE_REQUEST
      This choice denies the job an additional labeled volume.  Abnormal status
      is returned to the job.  Selection of this choice also allows you to
      explain why the additional volume was denied.  For example:

      2 your account/project has exceeded its budget for tape volumes

      Your explanation is returned to the job within the abnormal status that
      is generated by this menu choice.
~"**
END_MESSAGE_MODULE CREATE_MODULE=YES
~"CREATE_MESSAGE_MODULE RMM$EXTEND_UNLABELED$US_ENGLISH
~"CREATE_BRIEF_HELP_MESSAGE
                     NOS/VE Unlabeled Volume List Extension Menu

 Status                : An additional UNLABELED (scratch) volume is requested.
 Group                 : ~P1
 Location              : ~P2
 Requested Density     : ~P3
 Requesting Family Name: ~P4
 Requesting User Name  : ~P5
 Previous External VSN : ~P6

    You have the following choices:

~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=CONTINUE_REQUEST
       1 - Identify the 1 to 6 character vsn of the volume you want to provide
           (i.e. 1 EVSN='string' or 1 EVSN=name).
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=TERMINATE_REQUEST
       2 - Terminate the request (include a reason with the menu selection).

~"**
~"CREATE_FULL_HELP_MESSAGE
      This menu is presented because a job is requesting an additional
      unlabeled volume.  An additional volume is required when the job
      exhausts the list of volumes identified by either a
      REQUEST_MAGNETIC_TAPE command or an ATTACH_FILE command.

      If you provide an additional volume, the job's volume list is
      automatically updated with the volume that you provide.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=CONTINUE_REQUEST
      This choice identifies the volume that is to be added to the job's
      volume list.  The job requires an unlabeled volume.  If you intend to
      provide the job with an additional volume, enter the EXTERNAL_VSN using
      this menu choice.

      You may enter the value in the form of a string or an SCL name.  A string
      representation is required either when the VSN begins with a number or
      when special characters are used in the VSN.  For example:

        To enter an SCL name: 1 EVSN=VE0496
        To enter a VSN beginning with a number: 1 EVSN='901204'
          The latter produces 901204 as the EXTERNAL_VSN.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=TERMINATE_REQUEST
      This choice denies the job an additional unlabeled volume.  Abnormal
      status is returned to the job.  Selection of this choice also allows
      you to explain why the additional volume was denied.  For example:

      2 your account/project has exceeded its budget for tape volumes

      Your explanation is returned to the job within the abnormal status that
      is generated by this menu choice.
~"**
END_MESSAGE_MODULE CREATE_MODULE=YES
~"CREATE_MESSAGE_MODULE RMM$GENERIC_ERR_REC$US_ENGLISH
~"CREATE_BRIEF_HELP_MESSAGE
                     NOS/VE Generic Error Recovery Menu

  Status            : A fatal ~P4 error occurred ~P5.
  Element           : ~P2
  External VSN      : ~P1
  Tape Failure Mode : ~P3

    You have the following choices:

~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=ATTEMPT_RECOVERY
       1 - Attempt recovery; another mount will be requested for this tape.
           Processing will continue after tape assignment and repositioning.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=NO_RECOVERY
       2 - No recovery; abnormal status is returned to the job.
~"**
END_MESSAGE_MODULE CREATE_MODULE=YES
~"CREATE_MESSAGE_MODULE RMM$INCORRECT_RVSN$US_ENGLISH
~"CREATE_BRIEF_HELP_MESSAGE
                   NOS/VE Incorrect Labeled Volume Menu

  Status           : Either you assigned the wrong LABELED volume or
                     the user supplied an incorrect EVSN or RVSN.
  Requested Volume : External VSN=~P2
                     Recorded VSN=~P1
  Assigned Element : ~P4
  Assigned Volume  : Recorded VSN=~P3

    You have the following choices:

~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=CONTINUE_REQUEST
       1 - Mount and assign the requested tape volume (~P2).
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=TERMINATE_REQUEST
       2 - Terminate the assignment (include a reason with the menu selection).
~"**
~"CREATE_FULL_HELP_MESSAGE
      The job requested a volume whose RECORDED_VSN was supposed to be ~P1.
      However, you used the ASSIGN_DEVICE command to assign a volume whose
      RECORDED_VSN is ~P3.  Verify that the correct volume is mounted on
      element ~P4.

      If the volume you mounted has an EXTERNAL_VSN of ~P2, the user is
      violating security or forgot the RECORDED_VSN.  In either case,
      choose selection 2.  Abnormal status is returned to the job.

      If the volume you mounted is not the requested volume, enter selection 1.
      The job's request will return to the VE_DISPLAY TAPE_MOUNT to allow you
      to assign the correct volume to the job.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=CONTINUE_REQUEST
      This choice retracts the incorrect assignment and causes the job's
      request to be returned to the VE_DISPLAY TAPE_MOUNT.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=TERMINATE_REQUEST
      This choice denies the job access to the volume.  Abnormal status is
      returned to the job.  Selection of this choice also allows you to
      explain why access was denied.  For example:

      2 a volume with the correct EXTERNAL_VSN could not be found

      Your explanation is returned to the job within the abnormal status that
      is generated by this menu choice.
~"**
END_MESSAGE_MODULE CREATE_MODULE=YES
~"CREATE_MESSAGE_MODULE RMM$LOADPT_ERR_REC$US_ENGLISH
~"CREATE_BRIEF_HELP_MESSAGE
                     NOS/VE Loadpoint Error Recovery Menu

  Status            : A fatal write error occurred at loadpoint.
  Element           : ~P2
  External VSN      : ~P1
  Tape Failure Mode : ~P3

    You have the following choices:

~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=ATTEMPT_RECOVERY
       1 - Attempt recovery - another mount will be requested after the tape
           unloads. If tape labels were destroyed by the fatal write error, do
           an INITIALIZE_TAPE_VOLUME with RVSN=~P4, after selecting
           this option.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=NO_RECOVERY
       2 - No recovery - a fatal error will be returned to the job.
~"**
END_MESSAGE_MODULE CREATE_MODULE=YES
~"CREATE_MESSAGE_MODULE RMM$MANUAL_MAINT$US_ENGLISH
~"CREATE_BRIEF_HELP_MESSAGE
                     NOS/VE Tape Maintenance Menu

  Status           : A tape volume is requested for maintenance action.
  Requested Volume : ~P1
  Required Element : ~P3
  Write Enable     : ~P2

    You have the following choices:

~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=ALLOW_MAINTENANCE
       1 - Allow the maintenance action on the required element using the
           requested volume; first, mount the volume on the required element.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=TERMINATE_REQUEST
       2 - Terminate the request (include a reason with this menu selection).
~"**
~"CREATE_FULL_HELP_MESSAGE
      This menu asks that you confirm or deny maintenance access to the
      volume and element requested.  If you allow the maintenance access, you
      must first mount the volume on the element.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=ALLOW_MAINTENANCE
      This choice enables maintenance action to the requested volume and
      element.  Before entering this selection:

        1. Write enable the volume, if indicated in the menu.
        2. Mount the volume on the element and make the element ready.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=TERMINATE_REQUEST
      This choice denies maintenance access to the element and the volume.
      Abnormal status is returned to the job.  Selection of this choice also
      allows you to explain why maintenance access was denied.  For example:

      2 the volume you requested is not on site

      Your explanation is returned to the job within the abnormal status that
      is generated by this menu choice.
~"**
END_MESSAGE_MODULE CREATE_MODULE=YES
~"CREATE_MESSAGE_MODULE RMM$RESERVE_TAPE$US_ENGLISH
~"CREATE_BRIEF_HELP_MESSAGE
                           NOS/VE Tape Reservation Menu

     Status          :  This job requires tape elements that are not ON.

     Element Density :  Required  ON  DOWN  OFF
       ~P1         ~P2
       ~P3         ~P4
       ~P5         ~P6
       ~P7         ~P8

    You have the following choices:

~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=ALLOW_RESERVATION
      1 - Allow the reservation (first make required elements available).
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=DISALLOW_RESERVATION
      2 - Disallow the reservation (include a reason with the menu selection).
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=WAIT_ON_RESERVATION
      3 - Specify the number of minutes the job must wait until the elements
          are available; the default is 30 minutes.
~"**
~"CREATE_FULL_HELP_MESSAGE
      The job is attempting to reserve more tape units than are currently
      available.  For each density required, four values are displayed:

        Required - the number of units needed by the job
        ON       - the number of units currently available to the job
        DOWN     - the number of units that are either in the DOWN
                   state or whose channel/controller is in the DOWN state
        OFF      - the number of units that are either in the OFF state
                   or whose channel/controller is in the OFF state

      Your configuration may contain tape units that support two densities,
      e.g. 800/1600 or 1600/6250.  If so, you may see a menu like this
      example; the configuration has 4 tape units that support 1600/6250:
         Element Density :  Required  ON  DOWN  OFF
           MT9$1600             2      3    0    1
           MT9$6250             2      3    0    1
      In this example menu, 4 units of the paired unit type are requested
      (2 of each density) and 1 unit of the 4 in the configuration is OFF.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=ALLOW_RESERVATION
      This choice allows the job to reserve the required number of elements.

      Before entering this selection, you must change the state of the needed
      element(s) to ON.  A tape unit may be described as DOWN or OFF in the
      menu either because the state of the tape unit is not ON or because the
      unit is not accessible.  A tape unit is not accessible when all channels
      or controllers connected to the tape unit are not ON.  Therefore, to
      make a tape unit accessible, you may need to change the state of any or
      all of the following: a channel, a controller, a tape unit.

      In the following example, element V60 is turned on:
      SOU/LCU
      LCU/CHANGE_ELEMENT_STATE element=v60 state=on
      LCU/QUIT
      SOU/
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=DISALLOW_RESERVATION
      This choice denies the job the additional elements.  Abnormal status
      is returned to the job.  Selection of this choice also allows you to
      explain why the additional elements were denied.  For example:

      2 it will be six hours before the elements could be made available

      Your explanation is returned to the job within the abnormal status that
      is generated by this menu choice.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=WAIT_ON_RESERVATION
      This choice allows you to place the job in wait for a specified number
      of minutes.  At the completion of the wait, this menu will reappear, if
      the required elements are still not available.

      For example, if the wait is expected to be 2 hours, enter 120 minutes:

         3 120

      The default wait time is 30 minutes.

      There are 1440 minutes in a day.
~"**
END_MESSAGE_MODULE CREATE_MODULE=YES
~"CREATE_MESSAGE_MODULE RMM$ROBOTIC_MONOPOLY$US_ENGLISH
~"CREATE_BRIEF_HELP_MESSAGE
                     NOS/VE Robotic Element Monopoly Menu

  Status            : This job is requesting a volume that is in a robotic
                      library, but the job already has all of the robotic
                      elements assigned to it.
  Requested Density : ~P1
  Requested Volume  : ~P2

    You have the following choices:

~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=CONTINUE_REQUEST
       1 - Eject volume ~P2 from the robotic library and mount it on an
           element that is not connected to the robotic library and
           that supports the required density: ~P1.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=TERMINATE_REQUEST
       2 - Terminate the request (include a reason with this menu selection).
~"**
~"CREATE_FULL_HELP_MESSAGE
      A job has reserved a number of elements of density ~P1.  Because
      NOS/VE did not know at the time the job issued its RESERVE_RESOURCE
      command where the job's volumes were located, it could not determine
      whether or not the required elements were all connected to the 5744
      Library.

      Your configuration has some elements of the required density that are
      connected to the 5744 Library and some that are not.

      The job has reached a deadlock.  The job has successfully mounted volumes
      on all of the available elements connected to the 5744 Library.  The next
      volume that the job is attempting to mount (~P2) is located
      in the 5744 Library but there are no more elements on which the volume
      can be mounted.

      You may remove the volume from the 5744 Library and manually mount it
      on an element that is not connected to the 5744 Library or you may
      return abnormal status to the job.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=CONTINUE_REQUEST
      This choice retracts the job's request for a robotic mount of the volume
      and causes the job's request to appear in the VE_DISPLAY TAPE_MOUNT.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=TERMINATE_REQUEST
      This choice denies the job access to the volume.  Abnormal status is
      returned to the job.  Selection of this choice also allows you to explain
      why access was denied.  For example:

      2 ~P2 is in the Library but you already have all of its units assigned

      Your explanation is returned to the job within the abnormal status that
      is generated by this menu choice.
~"**
END_MESSAGE_MODULE CREATE_MODULE=YES
~"CREATE_MESSAGE_MODULE RMM$ROBOTIC_MAINT$US_ENGLISH
~"CREATE_BRIEF_HELP_MESSAGE
                     NOS/VE Tape Maintenance Menu

  Status           : A tape volume is requested for a maintenance action.
  Requested Volume : ~P1
  Required Element : ~P3
  Write Enable     : ~P2

    You have the following choices:

~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=ALLOW_MAINTENANCE
       1 - Allow the maintenance action on the required element using the
           requested volume (~P1).
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=TERMINATE_REQUEST
       2 - Terminate the request (include a reason with this menu selection).
~"**
~"CREATE_FULL_HELP_MESSAGE
      This menu asks that you confirm or deny maintenance access to the
      volume and element requested.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=ALLOW_MAINTENANCE
      This choice enables maintenance action to the requested volume and
      element.  The volume will be automatically mounted by the 5744 Library.

~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=TERMINATE_REQUEST
      This choice denies maintenance access to the element and the volume.
      Abnormal status is returned to the job.  Selection of this choice also
      allows you to explain why maintenance access was denied.  For example:

      2 please defer maintenance until after 5 PM

      Your explanation is returned to the job within the abnormal status that
      is generated by this menu choice.
~"**
END_MESSAGE_MODULE CREATE_MODULE=YES
~"CREATE_MESSAGE_MODULE RMM$WRITE_DISABLED$US_ENGLISH
~"CREATE_BRIEF_HELP_MESSAGE
                 NOS/VE Robotic Volume Write Disabled Menu

  Status          : The user requested a robotically mounted volume
                    for write access but the volume is not write enabled.
  Assigned Volume : ~P2

    You have the following choices:

~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=ALLOW_WRITE_ACCESS
       1 - Allow write access to the volume.  Before making this selection
           you must: EJECT the volume ~P2 from the library, write-enable the
           volume, and ENTER the volume in the library.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=TERMINATE_REQUEST
       2 - Terminate the assignment (include a reason with the menu selection).
~"**
~"CREATE_FULL_HELP_MESSAGE
      The job has requested write access to a volume located in the 5744
      Library, but the volume is not write enabled.

      You must either allow write access to the volume or return abnormal
      status to the job.

~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=ALLOW_WRITE_ACCESS
      This choice allows write access to the volume by the job.  Choose
      this selection only if the user is authorized to write on the volume.

      To enable writing, you must first go to the 5744 Console and do the
      following:

        1. EJECT volume ~P2 from the 5744 Library.
        2. Write enable the volume by turning the thumbwheel until the white
           dot (or other write disable symbol) is no longer visible.
        3. ENTER the volume back into the 5744 Library.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=TERMINATE_REQUEST
      This choice denies the job write access to the element.  Abnormal status
      is returned to the job.  Selection of this choice also allows you to
      explain why write access was denied.  For example:

      2 you are not authorized for write access to this volume

      Your explanation is returned to the job within the abnormal status that
      is generated by this menu choice.
~"**
END_MESSAGE_MODULE CREATE_MODULE=YES
~"CREATE_MESSAGE_MODULE RMM$WRITE_ERROR_RECY$US_ENGLISH
~"CREATE_BRIEF_HELP_MESSAGE
                     NOS/VE Write Error Recovery Menu

  Status            : A fatal write error occurred at block ~P4.
  Element           : ~P2
  External VSN      : ~P1
  Tape Failure Mode : ~P3

    You have the following choices:

~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=CONTINUE_SAME_VOLUME
       1 - Attempt recovery - another mount is requested for this volume.
           Processing continues after volume assignment and repositioning.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=NO_RECOVERY
       2 - No recovery - a fatal error will be returned to the job.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=CONTINUE_NEXT_VOLUME
       3 - Attempt recovery - the current volume is closed and writing
           continues on the next volume. This option should only be used
           after a tape media error that was not corrected by Option 1.
~"**
END_MESSAGE_MODULE CREATE_MODULE=YES
~"CREATE_MESSAGE_MODULE RMM$WRONG_LABEL_TYPE$US_ENGLISH
~"CREATE_BRIEF_HELP_MESSAGE
                   NOS/VE Unlabeled Tape Assignment Menu

  Status           : The assigned volume is UNLABELED but the user requested
                     a LABELED volume.
  Requested Volume : External VSN=~P2
                     Recorded VSN=~P1
  Assigned Element : ~P3

    You have the following choices:

~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=ASSIGN_LABELED_VOLUME
       1 - Mount and assign the requested LABELED tape volume (~P2).
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=TERMINATE_REQUEST
       2 - Terminate the assignment (include a reason with the menu selection).
~"**
~"CREATE_FULL_HELP_MESSAGE
      The job requested a labeled volume but you used the ASSIGN_DEVICE command
      to assign an unlabeled volume to the job.  The EXTERNAL_VSN is ~P2.
      Verify that the correct volume is mounted on element:
      ~P3.

      If the correct volume was assigned, you must choose selection 2 to
      prevent the assignment.

      If an incorrect volume was assigned, choose selection 1.  The job's
      request will reappear in the VE_DISPLAY TAPE_MOUNT to allow you to
      correct the assignment.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=ASSIGN_LABELED_VOLUME
      This choice allows you to assign the correct labeled volume to the
      job.  You will again see the job's request in the VE_DISPLAY TAPE_MOUNT.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=TERMINATE_REQUEST
      This choice denies the job access to the unlabeled volume.  Abnormal
      status is returned to the job.  Selection of this choice also allows
      you to explain why access was denied.  For example:

      2 you are not authorized access to this volume

      Your explanation is returned to the job within the abnormal status that
      is generated by this menu choice.
~"**
~"END_MESSAGE_MODULE CREATE_MODULE=YES
~"  CREATE_MESSAGE_MODULE RMM$CREBUV_BUV_MENU$US_ENGLISH
~"CREATE_BRIEF_HELP_MESSAGE
                          Tape Volume Initialization Menu

 Volume Status : Blank Unlabeled volume
 Tape Element  : ~P2

 This volume is blank unlabeled and contains no data.

 You have the following choices:

~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=CONTINUE_CREBUV
      ~P1- Unlabels this blank unlabeled tape volume.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=ABORT_CREBUV
      ~P1- Terminates the initialization of this tape volume.
~"**
~"CREATE_FULL_HELP_MESSAGE
      This menu allows you to confirm that the correct tape volume is mounted,
      and that it contains no data.

      Press RETURN/NEXT to return to the menu.  When the menu reappears, if
      you want additional help about a menu choice, enter the choice number
      followed by ?.  For example, enter 2? to obtain help information about
      choice 2.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=CONTINUE_CREBUV
      This choice proceeds with the creation of a blank unlabeled volume
      even though the volume is already blank unlabeled.  Three tapemarks
      will be written at the beginning of the volume.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=ABORT_CREBUV
      This choice terminates the initialization of the tape volume.  The
      volume is not modified and remains blank unlabeled.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=PROMPT
  Enter choice or ? for HELP:
~"**
END_MESSAGE_MODULE CREATE_MODULE=YES
~"  CREATE_MESSAGE_MODULE RMM$CREBUV_LE_MENU$US_ENGLISH
~"CREATE_BRIEF_HELP_MESSAGE
                          Tape Volume Initialization Menu

 Volume Status : Labeled volume whose first file is expired
 Tape Element  : ~P2

 The following information is currently on the volume:

   Volume Identifier (Recorded VSN) : ~P3
   Owner Identifier                 : ~P4
   Character Set                    : ~P5
   Expiration Date                  : ~P6
   File Accessibility               : ~P7
   Label Standard Version           : ~P8
   Volume Accessibility             : ~P9

 You have the following choices:

~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=CONTINUE_CREBUV
      ~P1- Unlabels this labeled tape volume.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=ABORT_CREBUV
      ~P1- Terminates the initialization of this tape volume.
~"**
~"CREATE_FULL_HELP_MESSAGE
      This menu allows you to confirm that the correct tape volume is mounted.
      This tape volume is labeled and the first file on the volume has expired.
      There may be other files on this volume that have not yet expired.
      Unless you are certain that you are initializing the correct volume and
      that all of the files on the volume have expired, you may want to contact
      the owner to confirm the volume serial number.

      Press RETURN/NEXT to return to the menu.  When the menu reappears, if
      you want additional help about a menu choice, enter the choice number
      followed by ?.  For example, enter 2? to obtain help information about
      choice 2.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=CONTINUE_CREBUV
      This choice proceeds with the creation of a blank unlabeled volume.
      Any data previously recorded on the volume will be lost.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=ABORT_CREBUV
     This choice terminates the initialization of the tape volume.  Any data
     previously recorded on the tape volume remains unchanged.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=PROMPT
  Enter choice or ? for HELP:
~"**
END_MESSAGE_MODULE CREATE_MODULE=YES
~"  CREATE_MESSAGE_MODULE RMM$CREBUV_LU_MENU$US_ENGLISH
~"CREATE_BRIEF_HELP_MESSAGE
                          Tape Volume Initialization Menu

 Volume Status : Labeled volume containing no expired files
 Tape Element  : ~P2

 The following information is currently on the volume:

   Volume Identifier (Recorded VSN) : ~P3
   Owner Identifier                 : ~P4
   Character Set                    : ~P5
   Expiration Date                  : ~P6
   File Accessibility               : ~P7
   Label Standard Version           : ~P8
   Volume Accessibility             : ~P9

 You have the following choices:

~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=CONTINUE_CREBUV
      ~P1- Unlabels this labeled tape volume.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=ABORT_CREBUV
      ~P1- Terminates the initialization of this tape volume.
~"**
~"CREATE_FULL_HELP_MESSAGE
      This menu allows you to confirm that the correct tape volume is mounted.
      This tape volume is labeled and contains no files that have expired.

      Unless you are certain that you are initializing the correct tape
      volume, you may want to contact the owner to confirm the volume serial
      number.

      Press RETURN/NEXT to return to the menu.  When the menu reappears, if
      you want additional help about a menu choice, enter the choice number
      followed by ?.  For example, enter 2? to obtain help information about
      choice 2.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=CONTINUE_CREBUV
      This choice proceeds with the creation of a blank unlabeled volume.
      Any data previously recorded on the volume will be lost.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=ABORT_CREBUV
      This choice terminates the initialization of the tape volume.  Any
      data previously recorded on the tape volume remains unchanged.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=PROMPT
  Enter choice or ? for HELP:
~"**
END_MESSAGE_MODULE CREATE_MODULE=YES
~"  CREATE_MESSAGE_MODULE RMM$CREBUV_URV_MENU$US_ENGLISH
~"CREATE_BRIEF_HELP_MESSAGE
                          Tape Volume Initialization Menu

 Volume Status : Read error at loadpoint
 Tape Element  : ~P2

 You have the following choices:

~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=CONTINUE_CREBUV
      ~P1- Creates a blank unlabeled volume.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=ABORT_CREBUV
      ~P1- Terminates the initialization of this tape volume.
~"**
~"CREATE_FULL_HELP_MESSAGE
      An error occurred at the load point when NOS/VE attempted to read the
      tape volume to find a label.  Consequently, the system cannot determine
      whether this is a blank tape or one that already contains data.

      This error can be caused by a tape unit problem.  Therefore, if you are
      certain you are initializing the correct tape volume, you may want to
      terminate the initialization and mount the volume on a different tape
      unit.

      If all of your tape units do not support the same densities, try mounting
      the volume on a unit that supports a different density to be certain
      that you are not initializing a volume containing valid data.

      Press RETURN/NEXT to return to the menu.  When the menu reappears, if
      you want additional help about a menu choice, enter the choice number
      followed by ?.  For example, enter 2? to obtain help information about
      choice 2.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=CONTINUE_CREBUV
      This choice proceeds with the creation of a blank unlabeled volume.
      Any data previously recorded on the volume will be lost.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=ABORT_CREBUV
      This choice terminates the initialization of the tape volume.  Any data
      previously recorded on the tape volume remains unchanged.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=PROMPT
  Enter choice or ? for HELP:
~"**
END_MESSAGE_MODULE CREATE_MODULE=YES
~"  CREATE_MESSAGE_MODULE RMM$CREBUV_UV_MENU$US_ENGLISH
~"CREATE_BRIEF_HELP_MESSAGE
                          Tape Volume Initialization Menu

 Volume Status : Unlabeled volume
 Tape Element  : ~P2

 This unlabeled volume contains data.

 You have the following choices:

~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=CONTINUE_CREBUV
      ~P1- Creates a blank unlabeled tape volume.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=ABORT_CREBUV
      ~P1- Terminates the initialization of this tape volume.
~"**
~"CREATE_FULL_HELP_MESSAGE
      This menu allows you to confirm that the correct tape volume is mounted,
      and that the data contained on it can be destroyed.

      Press RETURN/NEXT to return to the menu.  When the menu reappears, if
      you want additional help about a menu choice, enter the choice number
      followed by ?.  For example, enter 2? to obtain help information about
      choice 2.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=CONTINUE_CREBUV
      This choice proceeds with the initialization of this tape volume using
      the proposed label information.  Any data previously recorded on the
      volume will be lost.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=ABORT_CREBUV
      This choice terminates the initialization of the tape volume.  Any data
      previously recorded on the tape volume remains unchanged.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=PROMPT
  Enter choice or ? for HELP:
~"**
END_MESSAGE_MODULE CREATE_MODULE=YES
~"  CREATE_MESSAGE_MODULE RMM$INITV_EXP_MENU$US_ENGLISH
~"CREATE_BRIEF_HELP_MESSAGE
                          Tape Volume Initialization Menu

 Volume Status : Labeled volume whose first file is expired
 Tape Element  : ~P2

 Review the following proposed volume information for accuracy:

                                    Current              Proposed
   Volume Identifier (Recorded VSN) : ~P3 ~P10
   Owner Identifier                 : ~P4 ~P11
   Character Set                    : ~P5 ~P12
   Expiration Date                  : ~P6 ~P13
   File Accessibility               : ~P7 ~P14
   Label Standard Version           : ~P8 ~P15
   Volume Accessibility             : ~P9 ~P16

 You have the following choices:

~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=CONTINUE_INITV
      ~P1- Initializes this labeled tape volume with the proposed values.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=ABORT_INITV
      ~P1- Terminates the initialization of this tape volume.
~"**
~"CREATE_FULL_HELP_MESSAGE
      This menu allows you to confirm that the correct tape volume is mounted
      and that the proposed label information is correct.  This tape volume
      already has a label and the first file on the volume has expired.
      There may be other files on this volume that have not yet expired.
      Unless you are certain that you are initializing the correct volume
      and that all of the files on the volume have expired, you may want to
      to contact the owner to confirm the volume serial number.

      Press RETURN/NEXT to return to the menu.  When the menu reappears, if
      you want additional help about a menu choice, enter the choice number
      followed by ?.  For example, enter 2? to obtain help information about
      choice 2.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=CONTINUE_INITV
      This choice proceeds with the initialization of this tape volume using
      the proposed label information.  Any data previously recorded on the
      volume will be lost.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=ABORT_INITV
     This choice terminates the initialization of the tape volume.  Any data
     previously recorded on the tape volume remains unchanged.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=PROMPT
  Enter choice or ? for HELP:
~"**
END_MESSAGE_MODULE CREATE_MODULE=YES
~"  CREATE_MESSAGE_MODULE RMM$INITV_RE_MENU$US_ENGLISH
~"CREATE_BRIEF_HELP_MESSAGE
                          Tape Volume Initialization Menu

 Volume Status : Read error at loadpoint
 Tape Element  : ~P2

 Review the following proposed volume information for accuracy:

      Volume Identifier (Recorded VSN) :   ~P3
      Owner Identifier                 :   ~P4
      Character Set                    :   ~P5
      Expiration Date                  :   ~P6
      File Accessibility               :   ~P7
      Label Standard Version           :   ~P8
      Volume Accessibility             :   ~P9

 You have the following choices:

~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=CONTINUE_INITV
      ~P1- Initializes this unreadable tape volume with the proposed values.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=ABORT_INITV
      ~P1- Terminates the initialization of this tape volume.
~"**
~"CREATE_FULL_HELP_MESSAGE
      An error occurred at the load point when NOS/VE attempted to read the
      tape volume to find a label.  Consequently, the system cannot determine
      whether this is a blank tape or one that already contains data.

      This error can be caused by a tape unit problem.  Therefore, if you are
      certain you are initializing the correct tape volume, you may want to
      terminate the initialization and mount the volume on a different tape
      unit.

      If all of your tape units do not support the same densities, try mounting
      the volume on a unit that supports a different density to be certain
      that you are not initializing a volume containing valid data.

      Press RETURN/NEXT to return to the menu.  When the menu reappears, if
      you want additional help about a menu choice, enter the choice number
      followed by ?.  For example, enter 2? to obtain help information about
      choice 2.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=CONTINUE_INITV
      This choice proceeds with the initialization of this tape volume using
      the proposed label information.  Any data previously recorded on the
      volume will be lost.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=ABORT_INITV
      This choice terminates the initialization of the tape volume.  Any data
      previously recorded on the tape volume remains unchanged.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=PROMPT
  Enter choice or ? for HELP:
~"**
END_MESSAGE_MODULE CREATE_MODULE=YES
~"  CREATE_MESSAGE_MODULE RMM$INITV_UL_MENU$US_ENGLISH
~"CREATE_BRIEF_HELP_MESSAGE
                          Tape Volume Initialization Menu

 Volume Status : Unlabeled volume
 Tape Element  : ~P2

 Review the following proposed volume information for accuracy:

      Volume Identifier (Recorded VSN) :   ~P3
      Owner Identifier                 :   ~P4
      Character Set                    :   ~P5
      Expiration Date                  :   ~P6
      File Accessibility               :   ~P7
      Label Standard Version           :   ~P8
      Volume Accessibility             :   ~P9

 You have the following choices:

~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=CONTINUE_INITV
      ~P1- Initializes this unlabeled tape volume with the proposed values.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=ABORT_INITV
      ~P1- Terminates the initialization of this tape volume.
~"**
~"CREATE_FULL_HELP_MESSAGE
      This menu allows you to confirm that the correct tape volume is mounted
      and that the proposed label information is correct.

      The system cannot tell whether this is a blank tape or one that already
      contains data.  Unless you are certain that you are initializing the
      correct volume, you may want to contact the owner, if known, to confirm
      the volume serial number.

      Press RETURN/NEXT to return to the menu.  When the menu reappears, if
      you want additional help about a menu choice, enter the choice number
      followed by ?.  For example, enter 2? to obtain help information about
      choice 2.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=CONTINUE_INITV
      This choice proceeds with the initialization of this tape volume using
      the proposed label information.  Any data previously recorded on the
      volume will be lost.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=ABORT_INITV
      This choice terminates the initialization of the tape volume.  Any data
      previously recorded on the tape volume remains unchanged.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=PROMPT
  Enter choice or ? for HELP:
~"**
END_MESSAGE_MODULE CREATE_MODULE=YES
~"  CREATE_MESSAGE_MODULE RMM$INITV_UNEXP_MENU$US_ENGLISH
~"CREATE_BRIEF_HELP_MESSAGE
                          Tape Volume Initialization Menu

 Volume Status : Labeled volume containing no expired files
 Tape Element  : ~P2

 Review the following proposed volume information for accuracy:

                                    Current              Proposed
   Volume Identifier (Recorded VSN) : ~P3 ~P10
   Owner Identifier                 : ~P4 ~P11
   Character Set                    : ~P5 ~P12
   Expiration Date                  : ~P6 ~P13
   File Accessibility               : ~P7 ~P14
   Label Standard Version           : ~P8 ~P15
   Volume Accessibility             : ~P9 ~P16

 You have the following choices:

~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=CONTINUE_INITV
      ~P1- Initializes this labeled tape volume with the proposed values.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=ABORT_INITV
      ~P1- Terminates the initialization of this tape volume.
~"**
~"CREATE_FULL_HELP_MESSAGE
      This menu allows you to confirm that the correct tape volume is mounted
      and that the proposed label information is correct.  This tape volume
      already has a label and contains no files that have expired.

      Unless you are certain that you are initializing the correct tape
      volume, you may want to contact the owner to confirm the volume serial
      number.

      Press RETURN/NEXT to return to the menu.  When the menu reappears, if
      you want additional help about a menu choice, enter the choice number
      followed by ?.  For example, enter 2? to obtain help information about
      choice 2.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=CONTINUE_INITV
      This choice proceeds with the initialization of this tape volume using
      the proposed label information.  Any data previously recorded on the
      volume will be lost.
~"**
~"CREATE_PARAMETER_HELP_MESSAGE NAME=ABORT_INITV
      This choice terminates the initialization of the tape volume.  Any
      data previously recorded on the tape volume remains unchanged.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=PROMPT
  Enter choice or ? for HELP:
~"**
END_MESSAGE_MODULE CREATE_MODULE=YES
~"CREATE_MESSAGE_MODULE RMM$ACTION_MESSAGES$US_ENGLISH
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=ROBOTIC_UNIT_UNAVAILABLE
                    NOS/VE Tape Action Message

  Status              : A volume is mounted on a robotic element whose state
                        is DOWN or OFF.
  Requested Volume    : ~P1
  Unavailable Element : ~P2

  Action: To allow this job to use the requested volume (~P1), it is
          suggested that you turn the element ON using the LCU subcommand
          CHANGE_ELEMENT_STATE.  If you cannot turn the element ON, you
          may DISMOUNT the volume at the 5744 Console (you may have to use
          the FORCE option, if the element is "in use").
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=UNIT_NOT_OPERATIONAL
                    NOS/VE Tape Action Message

  Status                : The assigned tape element is NOT OPERATIONAL.
  Assigned Element      : ~P1
  Assigned Volume       : ~P2
  Requested Density     : ~P3
  Write Enable Required : ~P4

  Action: If you assigned the wrong element to this job, enter:
            /SOU REASSIGN_DEVICE ~P1
          Otherwise, make the assigned element operational.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=UNIT_NOT_READY
                    NOS/VE Tape Action Message

  Status                : The assigned tape element is NOT READY.
  Assigned Element      : ~P1
  Assigned Volume       : ~P2
  Requested Density     : ~P3
  Write Enable Required : ~P4

  Action: If you assigned the wrong element to this job, enter:
            /SOU REASSIGN_DEVICE ~P1
          Otherwise, ready the assigned element.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=UNIT_NOT_WRITE_ENABLED
                    NOS/VE Tape Action Message

  Status                : The assigned volume is NOT WRITE ENABLED.
  Assigned Element      : ~P1
  Assigned Volume       : ~P2
  Requested Density     : ~P3

  Action: If you assigned the wrong element to this job, enter:
            /SOU REASSIGN_DEVICE ~P1
          Otherwise, write enable the volume (~P2) and remount it on
          element ~P1.
~"**
END_MESSAGE_MODULE CREATE_MODULE=YES
~"CREATE_MESSAGE_MODULE RMM$JOB_STATUS_MSGS$US_ENGLISH
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=WAIT_FOR_FORCE
 Forcibly dismounting element ~P1.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=WAIT_FOR_DISMOUNT
 Dismounting ~P1 from element ~P2.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=WAIT_FOR_MOUNT
 Mounting ~P1 on element ~P2.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=WAIT_FOR_QUERY
 Querying robotic library for volume ~P1.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=WAIT_TAPE_UNIT
 ~P1 Waiting for tape unit.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=WAIT_MANUAL_MOUNT
 ~P1 Waiting for mount of volume ~P2.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=WAIT_ROBOTIC_UNIT
 ~P1 Volume ~P2 waiting for robotic element.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=WAIT_SCRATCH_VOLUME
 Waiting for operator to supply an additional volume.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=WAIT_SERVER_RETRY
 ~P1 Requesting volume ~P2 - server retrying.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=WAIT_UNITS_BUSY
 ~P1 Waiting for busy element(s).
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=WAIT_UNITS_UNAVAILABLE
 ~P1 Waiting ~P2 minute(s) - no element available.
~"**
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=WAIT_VSN_BUSY
 ~P1 Waiting for busy volume ~P2.
~"**
END_MESSAGE_MODULE CREATE_MODULE=YES
~"CREATE_MESSAGE_MODULE RMM$VOL_CLASSIFY$US_ENGLISH
~"CREATE_PARAMETER_PROMPT_MESSAGE NAME=VOLUME_CLASSIFICATION

 ~P1

   ~P2

   ~P3
~"**
END_MESSAGE_MODULE CREATE_MODULE=YES
